中国电子技术网
设为u乐国际娱乐官网 网站地图 加入收藏
 
  1. MCU|FPGA|嵌入式|模拟设计|RF|电源管理|传感器|测试测量|LED|DSP|存储器|AC/DC转换器|DC/DC转换器|放大器|铁电存储|
  1. 智能可穿戴|智能汽车|5G技术|智能医疗|智能照明|无人机|VR|智能电源|3D打印|机器人|智能农业与环境|智能教育|u乐国际娱乐官网
  1. u乐国际娱乐官网 >  解决方案 >  [原创] TI DRV10987 50W三相无传感器BLDC马达驱动方案

[原创] TI DRV10987 50W三相无传感器BLDC马达驱动方案

关键词:工业控制 马达控制 BLDC DRV10987 时间:2018-04-10 10:43:05       作者:TI       来源:u乐国际娱乐官网

TI公司的DRV10987是50W 12V-24V三相无传感器BLDC马达驱动器,集成了功率MOSFET,提供连续驱动电流高达2A,马达工作电压6.2V-28V,集成了降压转换器5V/100mA,LDO 3.3V/20mA,主要用在空气净化器和加湿器,三向BLDC和PMSM马达,烘干循环风机,排水和水泵,台扇和吊扇.本文介绍了DRV10987主要特性,框图,应用电路图以及评估模块DRV10987 EVM主要特性,电路图,材料清单.

The DRV10987 device is a 3-phase sensorless 180°sinusodial motor driver with integrated powerMOSFETs, which can provide continuous drivecurrent up to 2 A. The device is specifically designedfor cost-sensitive, low-noise, low-external-componentcount fan and pump applications.™

The DRV10987 device delivers current to the motorwith supply voltage as low as 6.2 V. If the powersupply voltage is higher than 28 V, the device stopsdriving the motor and protects the DRV10987circuitry.

The DRV10987 device uses a proprietary sensorless control scheme to provide continuous sinusoidal drive,which significantly reduces the pure tone acoustics that typically occur as a result of commutation. The interfaceto the device is designed to be simple and flexible. The motor can be controlled directly through PWM, analog, orI2C inputs. Motor speed feedback is available through both the FG pin and the I2C interface simultaneously.

The DRV10987 device features an integrated buck regulator to step down the supply voltage efficiently to 5 V forpowering both internal and external circuits. The 3.3-V LDO also may be used to provide power for externalcircuits. The standby-mode (8.5 mA) version (DRV10987S) leaves the regulator running, and the sleep-mode (48μA) version (DRV10987D) shuts the regulator off. Throughout this data sheet, the DRV10987 part number isused for both devices, that is, DRV10987D (sleep version) and DRV10987S (standby version), except for specificdiscussions of sleep vs standby functionality.

An I2C interface allows the user to rEPROgram specific motor parameters in registers and to program theEEPROM to help optimize the performance for a given application. The DRV10987 device is available in athermally-efficient HTSSOP, 24-pin package with an exposed thermal pad. The operating ambient temperature isspecified from –40℃ to 125℃.

DRV10987主要特性:

1• Operation Voltage Range:
– Motor Operation, 6.2 V to 28 V
• Total Driver H + L rDS(on)
– 250 mΩ at TA = 25℃
• Drive Current: 2-A Continuous Winding Current(3-A Peak)
• Sensorless Sinusoidal 180° Commutation Scheme
• Configurable Output PWM Slew Rate andFrequency for EMI Management
• Initial Position-Detect Algorithm to Avoid Back-Spin During Start-Up
• No External Sense Resistor Required
• Flexible User Interface Options:
– I2C Interface: Access Registers for Commandand Feedback
– Dedicated SPEED Pin: Accepts Either Analogor PWM Input
– Dedicated FG Pin: Provides TACH Feedback
– Spin-Up Profile Can Be Customized WithEEPROM
– Forward-Reverse Control With DIR Pin
• Integrated Buck Converter, 5‑V, 100-mA
• Integrated LDO, 3.3‑V, 20-mA
• Standby Current, 8.5-mA
• Supply Current of 8.5 mA With Standby Version(DRV10987S)
• Supply Current of 48 μA With Sleep Version(DRV10987D)
• Protection Features
– Overcurrent Protection (Phase-to-Phase,Phase-to-GND and Phase-to-VCC Short
Circuits)
– Lock Detection to Detect Rotor Lock Condition
– Anti-Voltage Surge (AVS) Protection
– Undervoltae Lockout (UVLO)
– Overvoltage Protection
– Thermal Warning and Shutdown
• Thermally Enhanced Package

DRV10987应用:

• Pedestal and Ceiling Fans
• Air Purifiers and Humidifiers
• Dryer Circulation Fans
• Drain and Water Pumps
• Three-Phase BLDC and PMSM Motors

图1.DRV10987功能框图

图2.DRV10987典型应用电路图

评估模块DRV10987 EVM

This user ’s guide provides complete details of the customer evaluation module (EVM) for the DRV10987device including hardware implementation, jumper configuration, and operating procedure to run 3-phaseBLDC motors. This EVM user’s guide is intended to be used with the DRV10987 Tuning Guide tooptimally tune a user motor.

The DRV10987 EVM is a complete solution for evaluating the DRV10987 12-V or 24-V, three-phasesensorless BLDC motor drivers. Device evaluation and configuration for specific applications is possiblewith the provided DRV10987 EVM GUI. This document describes the kit details and explains the functionsand locations of test points, jumpers, and connectors present on the kit. This document is also a quickstartguide for using the GUI to tune a motor for application. For detailed information about the operatingmodes of the DRV10987 device


图3.评估模块DRV10987 EVM外形图

评估模块DRV10987 EVM主要特性:

• DRV10987 EVM board
• USB2ANY communication board for I2C GUI interaction
• USB cable
• 10-pin ribbon cable to connect the USB2ANY and DRV10987 EVM
• DRV10987 EVM GUI
The DRV10987 EVM boards and GUI are designed to work together to evaluate the device features.

图4.评估模块DRV10987 EVM PCB打印图

图5.评估模块DRV10987 EVM电路图
评估模块DRV10987 EVM材料清单:

详情请见:
http://www.ti.com/lit/ds/symlink/drv10987.pdf
http://www.ti.com/lit/ug/slou476/slou476.pdf
drv10987.pdf
slou476.pdf

 
猜你喜欢
  1. 验证码: 点击换一张
  2. 注册|忘记密码?
u乐国际娱乐官网 中国电子行业研发工程师一站式服务平台 关于u乐国际娱乐官网| 广告招商| 联系我们| 招聘信息| 友情链接| u乐国际娱乐官网导航| 手机u乐国际娱乐官网 |   u乐国际娱乐官网官方微博 Copyright © 2000- u乐国际娱乐官网 版权所有      粤ICP备17063136号-2      增值电信业务经营许可证粤B2-20050142      京公网安备11010802010546号 Tel: 010-86463036, 0755-33322333     Fax: 0755-33322099
u乐国际娱乐官网